S-Shaped Ceiling

Product Features

Deep square-edge and beveled-edge versions each use their corresponding carrier.
Carrier retaining clips secure the strips; folded ends form end-to-end joints.
The S-profile has a 300 mm face and 29 mm edge height, with 0.70–0.95 mm sheet thickness.

Material: Aluminum strip
Length: Up to 6,000 mm
Thickness increments: 0.05 mm within the thickness ranges
Panel layout: Linear strips with matching carriers

Request This Product View Specifications

Moisture resistance
Recyclable aluminum
Color retention*
Acoustic options*
Heat dissipation*
Lightweight & workable

*Color retention depends on the finish. Sound absorption requires a specified acoustic assembly; heat dissipation depends on the open or perforated layout.

Product Data

Specifications & Size Options

Technical overview
Item	Specification
Material	Aluminum strip
Length	Up to 6,000 mm
Thickness increments	0.05 mm within the thickness ranges
Panel layout	Linear strips with matching carriers

Size and configuration options
Face width (mm)	Edge height (mm)	Thickness (mm)
300	29	0.70–0.95

Dimensions are in millimeters unless another unit is shown. Final sizes, finish and matching components are confirmed on the approved product schedule.

System Detail

Construction & Installation

Deep square-edge S-shaped strips

Deep square-edge S-strip assembly — numbered English component reference — Enlarge drawing & English key

Reading the Drawing

Use square-edge S strips with the corresponding deep square-edge carrier. The component profile and assembly section identify this connection.

Numbered Component Key

Match each number to the label below. Dimensions shown on the drawing are in millimeters unless noted.

M8 galvanized hanger rod
38/50 main-carrier hanger
Deep square-edge carrier
Deep close-joint carrier
Deep-profile carrier
Strip-carrier hanger
Deep square-edge S strip
Widths: 150 / 200 / 300 mm
Galvanized hanger rod
38/50 main carrier
Width

Installation Steps

Measure the finished ceiling elevation from the design drawings. Mark the level line and fix the perimeter angle along the walls.
Establish the installation direction. Drill suspension points in the structural ceiling at no more than 1,200 mm spacing and secure the galvanized hanger rods with expansion anchors.
Fit the main-carrier hangers and light-steel main carriers. Adjust their height and level, keeping the carriers parallel.
Use strip hangers to connect the deep square-edge strip carriers to the main carriers. Level the secondary carriers; keep them parallel to one another and perpendicular to the main carriers.
Fit the square-edge S-shaped strips into the matching secondary-carrier clips, working in one direction.
Measure perimeter panels on site, cut them to fit and support their edges on the perimeter angle.
Keep hands clean during installation. Avoid sweat, oil and other contamination on the finished surface.

Deep beveled-edge S-shaped strips

Deep beveled-edge S-strip assembly — numbered English component reference — Enlarge drawing & English key

Reading the Drawing

Use beveled-edge S strips with the deep beveled-edge carrier shown here. Do not substitute the square-edge carrier.

Numbered Component Key

Match each number to the label below. Dimensions shown on the drawing are in millimeters unless noted.

M8 galvanized hanger rod
38/50 main-carrier hanger
Deep beveled-edge carrier
Light-steel main carrier
Strip-carrier hanger
Deep beveled-edge S strip
Width: 300 mm
Galvanized hanger rod
38/50 main carrier
Width
38/50 light-steel main carrier

Installation Steps

Measure the finished ceiling elevation from the design drawings. Mark the level line and fix the perimeter angle along the walls.
Establish the installation direction. Drill suspension points in the structural ceiling at no more than 1,200 mm spacing and secure the galvanized hanger rods with expansion anchors.
Fit the main-carrier hangers and light-steel main carriers. Adjust their height and level, keeping the carriers parallel.
Use strip hangers to connect the deep beveled-edge strip carriers to the main carriers. Level the secondary carriers; keep them parallel to one another and perpendicular to the main carriers.
Fit the beveled-edge S-shaped strips into the matching secondary-carrier clips, working in one direction.
Measure perimeter panels on site, cut them to fit and support their edges on the perimeter angle.
Keep hands clean during installation. Avoid sweat, oil and other contamination on the finished surface.

These system details explain the illustrated assembly. Anchor selection, structural capacity and final suspension spacing must follow the approved project drawings and local requirements. Different carrier configurations are not interchangeable.